尽善尽美——儒家思想对中国设计的启示

经过几千年的发展和接受,儒家逐步确立了在中国主流意识形态中的“正典”地位。但应该承认,我们对于儒家的接受并不是不加批判全盘照搬的。在这两千多年的时间里,社会生活和意识形态领域所发生的重大变化我们不可能视而不见,而儒家思想恰恰有很大一部分是属于社会学科范畴之内的,在今天明显已经失去积极的意义(比如一些封建宗法),对此当然不能过分坚持,否定发展。因此,对于当今海外的“新儒家”的一些做法,可以欣赏他们对于中国传统文化的热忱,但必须承认那只是一部分知识分子的精英心态,从社会学的眼光看,的确过于保守,不利于文化的创造,特别是不能适应于现代艺术和设计的发展。本文希望区分出儒家思想中具有时代性和永恒性两个方面的内容,在对其已没有价值的社会伦理思想自觉进行发展的同时,对其永恒的东西进行一种当代的阐释。     

基于多边限定的室内定位方法设计与系统实现

随着基于位置服务（Location Based Services，LBS）的发展与智能移动设备的普及，室内定位算法与系统受到了广泛研究与关注。为提高室内定位精度、增强系统鲁棒性，提出了基于多边限定的fingerprint定位方法。基于Wi-Fi RSSI（Received Signal Strength Indication）信号处理建立离线fingerprint数据库；通过对拟合距离-RSSI函数分析，提出了多边限定的方法确定一个最佳参考点（Reference Point，RP）集合，缩小在线定位阶段的搜索范围。在此基础上，再利用fingerprint定位方法进行定位。此外，实现了基于提出方法的室内定位系统原型用于算法性能评估。通过大量真实场景实验分析、验证了相较于传统fingerprint方法，基于多边限定的fingerprint定位方法能有效提高室内定位精度，增强系统鲁棒性。     

钻井机器人的连续油管钻压和钻速控制模型

连续油管钻井机器人利用机身内外的钻井液压力差作为动力源，可在牵引连续油管的同时加载钻压。以钻井机器人为基础，建立连续油管钻柱动力学模型，并推导出通过钻井液排量控制钻压和钻速的单参数控制数学模型；对钻井机器人引入调速回路，建立具有调速功能的钻柱动力学模型；在溢流阀调定压力大于机身内外压差时，推导出利用钻井液排量和节流阀流通面积两种参数控制钻压、钻速的数学模型，在溢流阀调定压力小于机身内外压差时，推导出利用钻井液排量、节流阀流通面积和溢流阀调定压力3种参数控制钻压、钻速的数学模型；以11.43 cm（4.5英寸）井眼为例，对上述3种数学模型进行了分析。分析结果表明：钻压、钻速随钻井液排量的增加基本呈线性增加，在钻井液排量大于0.005 m³/s时，钻井机器人能够向前爬行，在钻井液排量大于0.005 7 m³/s时，钻头能够正常钻进；调节节流阀流通面积和溢流阀调定压力，可以在一定范围内无级调钻压和钻速；3种控制方法相结合，可以实现小排量、大钻压，及大排量、小钻压等钻井参数的控制。以控制模型为基础，针对不同井下工况建立钻进工艺的专家数据库，以钻井机器人为"大脑"，结合井下随钻测量数据就能够实现闭环控制，自动钻进。     

Revisiting the Parallel Strategy for DOACROSS Loops

Journal of Computer Science and Technology - DOACROSS loops are significant parts in many important scientific and engineering applications, which are generally exploited pipeline/wave-front...     

Effect of preparation method on physicochemical properties and catalytic performances of LaCoO_3 perovskite for CO oxidation

Perovskite oxides LaCoO_3 prepared by templating, co-precipitation and sol-gel method with different complexants were systematically characterized and its catalytic performances for CO oxidation were investigated. The samples were characterized by X-ray diffraction, thermogravimetry analysis and differential scanning calorimetry, N_2 physisorption, transmission electron microscopy, temperature program reduction of hydrogen, temperature program desorption of oxygen and X-ray photoelectron spectroscopy measurement, results of which show that the properties of LaCoO_3, such as surface morphology, surface area, surface compositions, redox capability, oxygen vacancy, as well as the calcination temperature and formation mechanism, depend intimately on the preparation method. Catalytic tests indicate that the sample prepared by carbon templating method shows the best activity for CO oxidation, with full CO conversion obtained at 135 ℃. In particular, the catalyst can be activated and significant increase of activity can be obtained with the increase of reaction time. The cyclic and longterm stability of catalysts were discussed and compared.     

Low-temperature synthesis of SiC nanowires with Ni catalyst

SiC nano wires were fabricated on the silicon substrate dipped with a layer of Ni catalyst at 900 ℃ by gas pressure annealing processing. The morphologies and crystal structures were determined by scanning electron microscopy(SEM), transmission electron microscopy(TEM)and X-ray diffraction(XRD). The results show that the assynthesized nanowires are β-SiC single crystalline with diameter range of 50-100 nm, and length of tens of micron by directly annealing at 900 ℃. The SiC nano wires grow along the [111] direction with highly uniform morphology. And the possible growth mechanism of SiC nano wires is proposed.The present work provides an efficient strategy for the production of high-quality SiC nano wires.     

提高加盖钢包自开率的研究与实践

首钢京唐300t钢包加盖后自开率明显下降，分析了加盖钢包自开率下降的机理，确定了主要原因是包衬温度升高后造成的液态渣回流。通过对引流砂的流动性、密度和渗钢性研究，设计了一种适用于加盖钢包的引流砂成分配比，并通过控制Al2O3和MgO含量，保证铬矿砂纯度。改进了钢包热修工艺，设计了针对加盖钢包的投砂操作和防钢渣回流措施。研究结果经推广使用后，钢包月不自开炉数由8～9炉降低至2炉以内，综合自开率达99.9%，双精炼工艺自开率达100%。